Sena Wireless Bluetooth Headsets – I put one on all my headsets: Law Abdinging Biker Store: shop.lawabidingbiker.com/collections/audio-headsets-amps-speakers-for-motorcycles RideTech Moto GoPro mounts for some helmet chin strap mounts, etc.: Ride Tech Moto: ridetechmoto.com/lawabidingbiker The instructions and a few other videos said to put the new collector loose and naked; Then insert the card sensor, fuel dispenser and injectors after it fits loosely. Man, the insertion of the small Torx 30 and 25 screws is a tight fit. In fact, there`s not enough room to put an L-shaped key in Torx`s heads until it`s fully seated and you`re done putting it on. I ended up using Torx tips from a pilot and a 1/4 box end key to tighten it. It was one of the closest installations I`ve done in a while. Biker Gripper Motorcycle Mobile Phone Mount-THE BEST ON THE MARKET-18 lbs Grip Stength! Law Abiding Biker Store: shop.lawabidingbiker.com/collections/bikergripper Dude Wipes Mint-For Keeping Your Butt Squeaky Clean: Amazon: www.lawabidingbiker.com/Fresh-Butt If you`re wondering what sets Law Abiding Biker video products apart from other instructional videos, here`s the list. Refuel, the seat is on and it`s time for a test drive. I first started it while my FP3 Vance and Hines was online to see if I had any error codes. There were a few related to the loss of connection to the throttle body, which was interesting since I hadn`t turned on the engine while I was working.
However, they cleared the minute the bike started. No new codes, no execution problems. It sounds strong, stronger perhaps, or maybe it`s my imagination. We rode our Harley Davidson & Indian motorcycles on the Old Spiral Highway in Idaho. It was built in 1917 and is a short highway with only 7.3 miles in length, but it is a motorcycle paradise with 64 turns in those miles. You drive through Lewiston, Idaho and down 2000 feet. It has a lot of twists, turns and spectacular returns. My suggestion is not to skip this highway if you are in the area.
It`s a secret gem. Now that I had the four distributor screws, I tightened them. Slip screws are another set that does not provide good access. You`ll need a long Allen for the gas side. Even then, put an extension with movement on it and you`ll probably be fine, but it`s tight. The clutch side is even worse. I ended up grabbing the 1/4-inch bit of the same set of drivers, plugged it in, and used an end key to spin it. Even then, it was painful to get this piece. The oil lines to the rear cylinder pass directly over the top of the manifold on the screws and there is no clearance. This is another place where the S&S video let me down. I wasn`t quite sure how far away the injectors were built into the manifold, and there was no image to show it. The video was shot almost entirely on the other side of the bike and there is no detailed look at this stage.
In the end, I removed them, installed them in the old unit, and when I was satisfied, I understood how they fit to bring them back to the new unit. It turned out that I had it well for the last half hour while trying to make her sit a little better. Quick-release helmet buckles – I put one on all my helmets: Amazon: amzn.to/3fmCfCD I started to worry. Not a big “W” concern, but a kind of harassment. I started wondering how my bike worked. An inexplicable slowdown here and there, my mileage hadn`t been great and there was a morning where he took care of it like it was a carburetor bike. It was a random problem here and there and none of it was coherent. It was only once in a while that you noticed that things were not going well. I arrive at 50 km and I have no babies. This potential problem made me think of the stupid plastic suction manifold when I woke up at night. Mini 3M Command Plastic Hook – to attach the Lavalier microphone cable to the headphones: Amazon: amzn.to/3raR2Tt Giant Squid Audio Omnidirectional Lavalier Microphone: Amazon: amzn.to/3Rjowtq Everything is tight and it`s time to reconnect the wires.
Or instead, it should be time to remove the load-bearing plate from the air filter and let the wiring harness work where it should have worked. Now that I had clarified this, the support plate was put back in place and the air filter installed. Universal Rotary Extension Arm J Hook Mount Set for Gopro Hero: Amazon: amzn.to/3DUptWh For reference, the dispenser I installed is part number 160-0241. It is listed as suitable for 2017-2021 M8 engines and is specifically suitable for replacing the OEM plastic intake manifold in large bores 124 and above.